收藏本站
AT86RF231
Generally, the Antenna Diversity algorithm is enabled with register bit ANT_DIV_EN (register
0x0D, ANT_DIV) set. In this case the control of an antenna diversity switch must be enabled by
register bit ANT_EXT_SW_EN (register 0x0D, ANT_DIV). The internal connection to digital
ground of the control pins pin 9 (DIG1) and pin 10 (DIG2) is disabled (refer to section 4.2), and
they feed the antenna switch signal and its inverse to the differential inputs of the RF Switch
(SW1).
Upon reception of a frame the AT86RF231 selects one antenna during preamble field detection.
The selected antenna is then indicated by register bit ANT_SEL (register 0x0D, ANT_DIV). After
the frame reception is completed, the antenna selection continues searching for new frames on
both antennas. However, the register bit ANT_SEL maintains its previous value (from the last
received frame) until a new SHR has been found, and the selection algorithm locked into one
antenna again. At this time the register bit ANT_SEL is updated again.
For transmission the antenna defined by register bits ANT_CTRL (register 0x0D, ANT_DIV) is
selected. If for example the same antenna is to be used for transmission as being selected for
reception, the antenna must be set using register bits ANT_CTRL, based on the value read from
register bit ANT_SEL. It is recommended to read register bit ANT_SEL after
IRQ_2 (RX_START).
The autonomous search and selection allows the use of Antenna Diversity during reception
even if the microcontroller does currently not control the radio transceiver, for instance in
Extended Operating Mode.
A microcontroller defined selection of a certain antenna can be done by disabling the automated
Antenna Diversity algorithm (ANT_DIV_EN = 0) and selecting one antenna using register bit
ANT_CTRL.
If the AT86RF231 is not in a receive or transmit state, it is recommended to disable register bit
ANT_EXT_SW_EN to reduce the power consumption or avoid leakage current of an external RF
switch, especially during SLEEP state. If register bit ANT_EXT_SW_EN = 0, output pins
DIG1/DIG2 are pulled-down to digital ground.
11.4.3
11.4.4
Antenna Diversity Sensitivity Control
Due to a different receive algorithm used by the Antenna Diversity algorithm, the correlator
threshold of the receiver has to be adjusted. It is recommended to set register bits PDT_THRES
(register 0x0A, RX_CTRL) to 3.
Register Description
Register 0x0A (RX_CTRL):
The RX_CTRL controls the sensitivity of the Antenna Diversity Mode
Bit
7
6
5
4
3
2
1
0
+0x0A
Reserved
PDT_THRES
RX_CTRL
Read/Write
Reset Value
R/W
1
R/W
0
R/W
1
R/W
1
R/W
0
R/W
1
R/W
1
R/W
1
? Bit [7:4] - Reserved
143
8111C–MCU Wireless–09/09
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
AT86RF232-ZX 2.4 GHZ ZIGBEE TRANSCEIVER
AT88CK201BK BRD CRYPTORF READER AT88RF1354
AT88SC-ADK2 KIT ARIS+ DK CRYPTOMEM/COMPANION
AT88SC3216CRF-MY1 IC EEPROM 32KBIT 13MHZ TAG
ATA-2001 LVDT AMPLIFIER
ATAB5429-9-B BOARD BASESTATN UHF RCVR 915MHZ
ATAB5749-3 BOARD XMITTER FOR 315MHZ ATA5749
ATAKSTK511-3 KIT RF MODULE 315MHZ FOR STK500
相关代理商/技术参数
AT86RF231-ZU 功能描述:射频收发器 2.4GHz Zigbee Transceiver RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray
AT86RF231-ZU_09 制造商:ATMEL 制造商全称:ATMEL Corporation 功能描述:Low Power 2.4 GHz Transceiver for ZigBee
AT86RF231-ZUR 功能描述:射频收发器 2.4GHz, Zigbee Transceiver RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray
AT86RF232-ZX 功能描述:射频收发器 2.4 GHZ ZIGBEE TRANSCEIVER RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray
AT86RF232-ZXR 功能描述:射频收发器 2.4 GHZ ZIGBEE TRANSCEIVER RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray
AT86RF233-ZF 功能描述:IC RF TXRX+MCU 802.15.4 32-VFQFN 制造商:microchip technology 系列:- 包装:托盘 零件状态:在售 类型:TxRx + MCU 射频系列/标准:802.15.4，通用 ISM > 1GHz 协议:6LoWPAN，Zigbee? 调制:O-QPSK 频率:2.4GHz 数据速率（最大值）:2Mbps 功率 - 输出:4dBm 灵敏度:-101dBm 存储容量:128B SRAM 串行接口:SPI 电压 - 电源:1.8 V ~ 3.6 V 电流 - 接收:11.3mA ~ 11.8mA 电流 - 传输:7.2mA ~ 13.8mA 工作温度:-40°C ~ 125°C 封装/外壳:32-VFQFN 裸露焊盘 标准包装:490
AT86RF233-ZFR 功能描述:IC RF TXRX+MCU 802.15.4 32-VFQFN 制造商:microchip technology 系列:- 包装:剪切带（CT） 零件状态:在售 类型:TxRx + MCU 射频系列/标准:802.15.4，通用 ISM > 1GHz 协议:6LoWPAN，Zigbee? 调制:O-QPSK 频率:2.4GHz 数据速率（最大值）:2Mbps 功率 - 输出:4dBm 灵敏度:-101dBm 存储容量:128B SRAM 串行接口:SPI 电压 - 电源:1.8 V ~ 3.6 V 电流 - 接收:11.3mA ~ 11.8mA 电流 - 传输:7.2mA ~ 13.8mA 工作温度:-40°C ~ 125°C 封装/外壳:32-VFQFN 裸露焊盘 标准包装:1
AT86RF233-ZU 功能描述:射频收发器 2.4GHz ZigBee Transceiver RoHS:否 制造商:Atmel 频率范围:2322 MHz to 2527 MHz 最大数据速率:2000 Kbps 调制格式:OQPSK 输出功率:4 dBm 类型: 工作电源电压:1.8 V to 3.6 V 最大工作温度:+ 85 C 接口类型:SPI 封装 / 箱体:QFN-32 封装:Tray